What's New » 'SWEEPER™' FOR COMPLETELY EMPTYING BULK BOXES OF RESIN WITHOUT OPERATOR INTERVENTION NOW PREVENTS DOWNTIME FOR CHANGEOVERS
'SWEEPER™' FOR COMPLETELY EMPTYING BULK BOXES OF RESIN WITHOUT OPERATOR INTERVENTION NOW PREVENTS DOWNTIME FOR CHANGEOVERS
New Dual Control System Switches between Adjacent Gaylord Boxes in Interconnected Sweeper™ Devices; also New Is a Larger Sweeper Model for Emptying European Octobins
TAMWORTH, STAFFORDSHIRE, UK, September 6, 2011: Maguire Products, Inc., has
eliminated downtime for changing from an empty bulk resin box to a full one by developing
a dual control system for its Sweeper™, a device that completely empties containers without
wasting operator time or resorting to cumbersome box tilters, it was announced today by
Maguire Europe. The company will introduce the Sweeper to the European market at Fakuma
2011 (Stand A7-7210).
Now available worldwide after being adopted by plastics processors in the U.S.A., the Sweeper
can be supplied in a size that accommodates European-style octobins, which hold 1,000 kg of
resin. Maguire also now offers its original model, sized for Gaylord boxes that hold 450 to 680
kg (1,000 to 1,500 lb), in two versions that accommodate vacuum line hoses with 1.5 and 2.5 in.
(38 and 64 mm) diameters, respectively. The larger octobin-sized model accommodates 64 mm
The key component in the new system for reducing changeover downtime is a dual control that
automatically switches from a Sweeper in an empty box to a second Sweeper in an adjacent full
one. The Sweepers are interconnected by means of a diverter valve. Once the switch takes place,
the operator can replace the empty box without an interruption in the transfer of resin to the
processing machine or dryer.
While the Sweeper normally operates only when the vacuum loading system is pulling material,
the dual control can be set to delay the switch from one Sweeper to the alternate between loader
cycles, allowing continued removal of resin until the Gaylord or octobin is empty. An automatic
switch to the alternate Sweeper prevents a stoppage in the flow of resin to the loader. In the event
that there is no material in the alternate box, the control system will alarm, alerting the operator.
Sweeper™ Leaves 'Only a Scattering of Pellets' Behind
"The Sweeper is easy to deploy, works with any standard loading system, and takes up only
a little more floor space than the Gaylord or octobin itself," said Paul Edmondson, general
manager of Maguire Europe. "Even as resin levels become very low, the device continues doing
its job without operator intervention, until there is nothing left in the bin but a scattering of
In both single- and dual-unit installations, each Sweeper continuously sweeps the length and
breadth of the top level of resin in the container, reaching into every corner, as it uses vacuum to
transfer the resin to a processing machine or dryer. The device descends along with the level of
resin in the Gaylord or octobin until the container is empty. Because The Sweeper removes resin
from the box without unwanted interruptions, there is no need for operators to stand by to ensure
that the processing machine does not run out of material.
The Sweeper is mounted on a structural steel stand that straddles the box, giving access to a
forklift truck or pallet jack for putting full boxes in place or removing empties. Above the box
is a set of vertical rails on which a counter-balanced trolley can move up and down. The trolley
carries a standard aluminum conveying tube, which in turn is coupled to a lower, rotating tube
that is driven by a very low-speed (1 rpm) gear motor.
The rotating action of the tube drives a transverse sweeping device that moves over the top of
the load of resin pellets like a sled through snow, driving pellets from the center of the box to the
sides. There the pellets are vacuumed up by the slotted end segment of a 0.9-m (3-ft.) flexible
hose that is affixed to the bottom of the rotating tube. As the vertical tube rotates, the flexible
hose is dragged along the top of the contents in a swept-back, trailing manner that enables it to
reach not only along the four sides of the box but into every corner.
MAGUIRE PRODUCTS, INC., headquartered in Aston, Pennsylvania, U.S.A., is the world's largest
supplier of gravimetric blenders and liquid color pumps and also manufactures loading systems, dryers,
auger feeders, and related equipment and software. Its customers include injection, blow, and rotational
molders, extrusion processors, and compounders. Founded in 1977, Maguire operates six manufacturing
facilities in Aston. The company maintains a network of distributors in the Americas and overseas and
has three sales and service subsidiaries that stock, sell, and service auxiliary equipment systems from
Maguire and its affiliate, Novatec, Inc.: Maguire Canada, Maguire Europe, and Maguire Asia. Visit
Maguire Products, Inc., 11 Crozerville Road, Aston, PA 19014 USA. Tel: 1-610-459-4300.
firstname.lastname@example.org. Maguire Canada, 299 Basaltic Road, Unit 1, Vaughan, Ontario L4K 4W8. Tel: 905-
879-1100. email@example.com. Maguire Europe, Vanguard, Tame Park, Tamworth, Staffordshire
B77 5DY United Kingdom. Tel: 44-1827-265-850. firstname.lastname@example.org. Maguire Europe
(Italy), Maguire Italia SRL, Via Cile, 14, 35127 Padova, Italy. Tel: 39-049-970-5429. Italia@maguire-
europe.com. Maguire Asia, Maguire Products Asia Pte Ltd., 45 Kallang Pudding Road, No. 01-02 Alpha
Building, Singapore 349317. Tel: 65-6848-7117. email@example.com. Maguire Asia (China),
Maguire Products Asia Co. Ltd., 7C-02 Majesty Building, 138 Pu Dong Avenue, Shanghai 200120 China.
Tel: 86-21-588-23410. firstname.lastname@example.org.